• Sunny Type HG0 HG1 HG2 Hydraulic Gear Oil Transfer Pump
  • Sunny Type HG0 HG1 HG2 Hydraulic Gear Oil Transfer Pump
  • Sunny Type HG0 HG1 HG2 Hydraulic Gear Oil Transfer Pump

Sunny Type HG0 HG1 HG2 Hydraulic Gear Oil Transfer Pump

Brand: YIHE

Product origin: CHINA

Delivery time: 10-30 days

Supply capacity: 300pcs/day

Model: HG0 HG1 HG2
Max Displacement: 8 cc/rev
Max Working Pressure: 31.5 Mpa
Shaft Speed Range: 600-3000 r/min
Rotation: Right from shaft end
Product Type: Internal Gear Pump

Sunny Type HG0 HG1 HG2 Hydraulic Gear Oil Transfer Pump

Hydraulic gear pump

Product detail presentation

Sunny Gear Pump

High efficiency, low noise and durable

sunny hydraulic pump

Fast speed and low noise

Hydraulic gear pump

low noise long life

Sunny Gear Pump

product feature:

1, the use of axial and radial pressure compensation design, even at low speed and low viscosity can still maintain high volumetric efficiency

2, ultra-low noise, the use of high strength cast iron and internal unique noise reduction design, so that the noise is lower.

3, very low flow and pressure pulsation, at low speed can be thrown to maintain stable flow and pressure output.

4, high pressure design, high pressure can reach 35MPa.

5, wide speed range, high speed up to 3000r/min.

6, can be combined to form a double pump.

7, not sensitive to oil pollution, long service life.

8, can be widely used with industry, such as plastic machine, shoe machine, die casting machinery and forklift industry hydraulic system. Especially suitable for energy saving systems with servo frequency drive

 

Product details

sunny hydraulic pump

 

MODEL

SIZE

DISP. cc/rev

PRESSURE bar

ROTATING SPEED r/min

WEIGHT kg

Rated

Max

Max

Min

HG0

8

8.0

250

300

3000

600

4.4

10

10.0

315

350

3000

600

4.6

13

13.3

315

3

 

3000

600

4.9

16

16.0

315

350

3000

600

5.2

20

20.0

315

350

3000

600

5.6

HG1

25

25.3

315

350

3000

200

14.5

32

32.7

315

350

3000

200

15

40

40.1

315

350

3000

200

16

50

50.7

315

350

3000

200

17

63

53.7

315

350

3000

200

18.5

HG2

80

81.4

315

350

3000

200

43.5

100

100.2

315

350

3000

200

45.5

125

125.3

315

350

3000

200

48

160

162.8

210

260

3000

200

52


Instructions for use

To protect your rights please read the following carefully

Pump Start-up Procedure 
Preparation Prior to Start-up 
The reservoir and circuit should be clean and free of dirt and debris prior to filling with fluid. 
Circuit Cleanup 
The reservoir should be charged with filtered hydraulic fluid. The fluid level should be sufficient to prevent vortexing at the suction connection to the pump inlet. It is good practice to clean the system by flushing and filtering, using an external slave pump. 
Filling Pump and Removing Air 
If the pump is mounted above the fluid level, it should be filled with fluid through the outlet port. If the pump is mounted below the fluid level, the pump outlet fitting (or other downstream fitting or plug) can be loosened to allow fluid to displace the air. It may be necessary to loosen the fill cap on the reservoir to allow the fluid to flow freely. When a solid stream of fluid with no observed air begins to drain through the loosened fitting, the fitting should be retightened. An air bleed valve in the outlet circuit is also recommended to remove trapped air. If such a device is used, the pump should be filled with fluid before start-up. In some cases, it may be possible to prime the pump by running the engine starter for five to ten seconds with the throttle and/or ignition switch in the "off" position. It will be necessary to loosen a fitting or plug in the pump outlet to allow air to escape. 
Pump Start-up 
All controls should be placed in the neutral position so the pump is unloaded when started. Start the engine and run at low idle. Once the pump is started, it should prime and pump within a few seconds. If it does not, make sure there are no restrictions between the reservoir and the inlet to the pump, and that there are no air leaks in the inlet line and connections.  Also, make sure that trapped air can escape from the outlet. Run at low engine idle for approximately five minutes. Then, while observing the reservoir fluid level, operate the implements. Extend all actuators to maximum safe limits to completely fill the system with fluid. Do not run with the fluid level below the "low" limit. Add fluid to the reservoir to bring the fluid to the proper fill level.

Hydraulic gear pump

Company Profile

We are Guangzhou Yisheng Machinery Equipment Co.,Ltd., which located in Foshan City, Guangdong Province, China. We have R&D department with about 5-10 engineers and designers. Our factory have over 100 skilled employees, our production facility have many advanced manufacturing equipments and testing equipments, such as numerical control lathe, the processing center, CNC milling machine, special CNC grinding machine, double grinding machine, automatic 3D measuring instrument, etc..


Our main products are hydraulic variable displacement vane pump, double pump, HVP high pressure variable displacement vane pump, PV2R1 & PV2R2 series,V&VQ series,T6&T7 series, SQP series and VQ series of fixed displacement vane pump and electrical motors for hydraulic application.


Our products are widely used for industrial machinery, NC lathe machine, shoe machinery, wood working machines, plastic machines, construction machines and various hydraulic system machinery. We also able to supply the customized products and services as per your spec. ,we are looking forward to cooperating with your company sincerely.

Sunny Gear Pump

 

Why choose us

1.The company established more than 10 years, old brand, worthy of trust,Has more than 1000k+ followers

2.The company's product category is complete, also have a variety of accessories to provide.

3.All products have been passed strict quality test before shipment, make sure high quality.

4.24H customer service,Please feel free to contact me if you have any questions.

5.One-year warranty, we have professional and technical personnel for docking, product quality is hard, and after-sales are guaranteed. After the one-year warranty is over, we can provide maintenance services for customers (this requires a fee).

sunny hydraulic pump

FAQ

Q: Are you trading company or manufacture?

A: We are factory

Q: How long is your delivery time?

A: Gernally it is 1-2days if the goods are in stock.It is 5-7days if the goods no stock.It is subject to order quantity.

Q: Do you provide sample,Is it free or extra?

A: We are willing to provide samples to test quality first, it is not for free because it is high value products. But sample cost can return in bulk order.

Q: What is the terms of payment?

A: 100% deposit or 30% deposit, 70% before shippment.

Q: How long is the warranty?

A: We offer 12 months warranty. 

Hydraulic gear pump

Related Products3
Product Tag
Get the latest price? We'll respond as soon as possible(within 12 hours)