PV2R24-33-153 Double Vane Pump | 100% Interchangeable with Yuken | YHDE
Brand: Yihe
Product origin: China
Delivery time: 10-20 days
Supply capacity: 300pcs/day
High-performance PV2R24 double hydraulic vane pump, 100% compatible with Yuken PV2R series. Factory-direct from YHDE with 9+ years of expertise. Dual-flow efficiency, ultra-low noise, and 21 MPa pressure rating. Fast global shipping. Get a technical quote today!
Facing Stalls on High-Tonnage Presses or Molding Lines Due to a Broken Yuken PV2R24 Pump? Restore Power in 48 Hours!
When a high-performance double vane pump loses pressure or suffers severe internal wear in your heavy plastic injection molding machinery, industrial press, or scrap baling equipment, waiting 12 to 16 weeks for expensive original imports directly drains your workshop's daily profitability.
Our premium Yuken-type PV2R24-33-153 High-Pressure Double Hydraulic Vane Pump serves as a seamless, 100% mechanical "drop-in" physical replacement. Built in our ISO-compliant source manufacturing facility with 9+ years of micro-tolerance hydraulic tooling mastery, this dual-flow pump restores native volumetric speed and high-pressure limits—slashing your procurement and MRO budget by up to 70%.
100% Physical Form Match: Mounting flanges, drive shaft keys, port configurations, and bolt holes match Yuken specs identically with zero pipeline modifications required.
Fast Factory Dispatch: Units are built, dynamic full-load bench tested to rated pressures, and shipped worldwide within 24-48 hours to eliminate costly facility downtime.
Technical Specifications & Operational Parameters
Cross-verify your equipment's operating pressure curves, required flow rates, and mounting envelopes using our master engineering data table below:
| Parameter Attribute | Front Pump Section (PV2R2 Frame) | Rear Pump Section (PV2R4 Frame) | Application System Advantage |
|---|---|---|---|
| Nominal Displacement | 33.0 cm³/rev (ml/r Code 33) | 153.0 cm³/rev (ml/r Code 153) | Combines high-volume primary output and secondary pilot/holding loops. |
| Max Operating Pressure | 21.0 MPa (210 bar / 3045 PSI) | 17.5 MPa (175 bar / 2538 PSI) | Ductile iron casting handles continuous heavy clamping loads without flexing. |
| Operating Speed Range | 750 - 1800 r/min (RPM) | 600 - 1800 r/min (RPM) | Standard speed limits compatible with industrial electric motors. |
| Average Operational Noise | Strictly Under 68 dB(A) | Circular arc vane profile dampens fluid pulsation for quiet workshops. | |
Model Ordering Nomenclature Decoded: PV2R24-33-153-F-REAA-41
| Code Segment | Technical Specifications Meaning | System Installation Alignment Reference |
|---|---|---|
| PV2R24 | Double High-Pressure Vane Pump Series (PV2R2 + PV2R4 frames) | Integrates dual pump cartridges inside a single heavy casting. |
| 33 / 153 | Nominal Displacements (33.0 ml/r Front / 153.0 ml/r Rear) | Calculates the exact volumetric output speed required for dual circuits. |
| F | Mounting Style: Flange Type Configuration | Directly matches original standard SAE/Japanese flange coupling alignments. |
| R | Clockwise (CW) Rotation Path (Viewed from shaft end) | Must align with the driving motor rotation path to prevent seal blowout. |
| EAA-41 | Port Connection Options & Design Sequence Number | Aligns inlet/outlet orientations to original plumbing configurations. |
Precision Tooling: Engineered for High Volumetric Output & Low Noise
Running a heavy double pump continuously under heavy workshop cycles demands extreme micro-dimensional accuracy. Non-specialized traders supply castings with unground landing zones, leading to early pressure bypass, high operating heat, and rapid volumetric decay. We eliminate these failure modes directly on our factory floor:
Circular Arc Vane Geometry: Our PV2R series incorporates dual-vane pin tracking mechanisms. Vanes are hydrostatically balanced under peak line pressures, significantly lowering friction against the stator ring and dropping noise below 68 dB(A) for comfortable workshop operations.
Sub-Micron CNC Profiling: Stator cam ring tracking contours and rotor side sealing plates are ground to sub-micron tolerances on specialized vertical CNC profile grinders, guaranteeing zero internal boundary leakage.
100% Full-Load Bench Test Validation: Every single PV2R24 double pump is dynamic tested up to its peak pressure limits on our hydraulic calibration bench. We verify both chambers simultaneously before crating.
Pro Maintenance Insight: Escape the Hostile "Sandpaper Effect"
When should you execute an urgent pump overhaul? If your central system starts presenting sudden cycle slowdowns under load, localized oil reservoir temperature spikes, or produces a harsh, high-frequency metallic screaming from the pump housing, internal vane tracking degradation has begun.
If your technical crew simply bolts a fresh new replacement pump onto the system without deep cleaning the circuit, these residual hard particles will act as an aggressive grit abrasive—creating a devastating "sandpaper effect". They will instantly score the freshly ground stator profile rings, destroying your new double pump within a few operating hours.
Mandatory Procedure: Meticulously drain and flush the reservoir tank, thoroughly scrub the suction intake strainers, and install a brand-new 10-micron absolute premium return fluid filter concurrently with the new pump unit installation.
Frequently Asked Questions: PV2R24 Series Double Pumps
1. Is this PV2R24-33-153 double pump 100% drop-in interchangeable with original Yuken pumps? +
2. What are the flow displacement and pressure capacities of each section in the PV2R24-33-153 double pump? +
3. Can we rebuild individual chambers using modular cartridge kits instead of buying a whole new pump? +
Request Direct Factory Wholesale Pricing Now
Looking to bypass third-party trading agent markups and heavy brand taxes? Secure micro-tolerance, low-noise PV2R24 series double vane pumps shipped directly from our precision manufacturing line today.
Get An Instant Factory Price Quote
